Make An Appointment

 

This article following next about Easy Shower Drain Installation Tips is fairly insightful. Read it yourself and decide what you think of it.

Upgrading a washroom is among the much more preferred home enhancement projects. Dealing with the plumbing for draining your shower can be exceptionally straightforward unless you go overboard.

 

 

Managing Your Own Shower Drainpipe Installment Task

Whether you are a bathtub or shower individual, lots of people look for shower only choices when acquiring a home. This straightforward truth means more than a few house owners invest a weekend break updating or setting up showers in their shower rooms. The good news is for you, it is a fairly easy process.

An enthusiast or frying pan refers to the straight surface area located at the bottom of the shower. The collection agency normally consists of a non-slip surface area a little banked towards the center or wherever the drain is located. Integrated with three to 4 inch walls around the side, the goal of your shower drain plumbing is to get the water to stream to and also down the drain.

You can literally construct a collector for your brand-new shower, yet you actually require to think of it. Do you truly want to enter the issues of getting the sloping appropriate, in addition to making certain every element of it is water-proof? And also I indicate every element! It is much easier to just purchase a pre-cast collector online or at your regional Lowes, Residence Depot or equipment shop. Building one may sound like a fantastic concept, yet you will possibly really feel in a different way after a couple of hours.

No matter just how you deal with getting a pan, you need to strive to utilize one that has the drain situated in the same area as the original frying pan. Relocating the drain pipes can be a job, especially if the builder utilized a special framing framework. If you are figured out to move the drain, you are mosting likely to need to cut down the pipe or extend it, which may mean destroying big chunks of the flooring. Put another way, you are mosting likely to be taking a look at a numerous weekend project.

Assuming we have our drainpipe aligned, the actual link is relatively simple. The water drainage pipe ought to be dealing with upright as much as the collector. It will often resemble a "U", which suggests it serves as a cleanout to maintain nasty scents from coming back up from the drainpipe. To connect the drainpipe, you are going to create a water limited connection in between a drain cap on the top of the frying pan and also the drainage pipe. Solutions differ, however you are commonly going to do this by placing a coupling item on the top of the water drainage pipeline. This is after that covered with gaskets and also literally screwed right into the drain cap. The drain cap should serve as a locknut, to wit, it screws straight onto the coupling.

The difficult part of this procedure is obtaining your drain cap to suit a watertight placement in the pan. This is achieved by backing off the drain cap when you make sure everything fits together. At that point, you put plumbing technicians putty around the bottom of the cap and then screw it back on. The putty ought to develop a limited seal between the cap and also the shower frying pan, which keeps water from trickling under it as well as right into the mounting under the shower.

Undoubtedly, washroom showers can be found in a wide variety of styles these days. If you buy a collection agency, they usually featured plumbing directions or the shop can keep in mind anything unusual you ought to understand. It seems complicated, yet is typically pretty simple. Have fun!

 

How To Install & Replace A Shower Drain In 5 Steps

 

Replacing a shower drain, or installing one for the first time, often requires a plumber, but if you’re confident in your DIY skills then you may be able to do it yourself. Your new shower drain should come with specific installation instructions, so take time to familiarise yourself with those before you get started. There are several types of shower drain, and the one you choose or are supplied with will depend on your shower tray, your pipes and the manufacturer’s recommendations. All Mira shower trays are compatible with compression-style shower drains, which attach to your home’s drainpipes with compression washers and nuts. Here’s an overview of how to install this type of drain.

 

How to install a compression-style drain

 

Please bear in mind that these are general instructions, and you should refer to the manufacturer’s recommendations to install your shower drain.

 

Trim the drainpipe

 

The drainpipe should come up to 2cm below the lip of the shower drain. You might need to lift the shower base on to mark the right height, and then remove it again before trimming the drainpipe with a hacksaw. Ensure the cut is flat and level.

 

Attach the drain assembly to the shower base

 

Apply silicone caulk to the lower rim of the drain assembly and insert it into the shower base from the top side of the base. This should be done before the base is put in place on the floor. Press the drain assembly firmly into place so that the caulk forms an even seal.

Slide the rubber washer and slip washer on to the drain assembly from underneath the shower base, then thread the drain nut on and tighten it with pliers.

Wipe away any excess caulk that has oozed out.

 

Put the shower base in position

 

Carefully position the shower base so that the drain assembly lines up with the drainpipe and fits inside it. It’s a good idea to get someone else to help out, and it’s usually easier to set the back of the base down first, and then lower the front of the base down.

 

Insert the compression gasket and nut

 

Slide the rubber compression gasket down into the drain opening so that it fits around the drainpipe. The top of the gasket should line up with the top of the pipe, or be slightly lower.

Drop the compression nut into the drain opening and use the fitting tool that will likely have been provided and a screwdriver to tighten the nut. As you tighten it, the gasket will be compressed against the drainpipe, creating a watertight seal.

 

Fit the metal strainer

 

Press the metal strainer into the drain opening, making sure the top surface is lower than the shower floor around it.

And there you have it, a brand-new shower drain! Allow the silicone to set for a full 24 hours before using the shower.

 

Cleaning and maintenance of your shower drain

 

Shower drains can quickly become clogged with hair and a build-up of product, which can lead to bad smells and can prevent your shower water from draining efficiently.

To maintain your shower drain, clear out any strands of hair that gather on the metal strainer after each shower. We recommend cleaning your shower drain thoroughly once a month using boiling water to loosen up soap scum and get things moving.

https://www.mirashowers.co.uk/blog/how-to/how-to-install-replace-a-shower-drain-in-5-steps/

 

I hope you enjoyed reading our part about Simple Steps for Installing a Shower Base. Thanks so much for spending some time to browse our posting. Loved our blog? Please share it. Help other people discover it. I appreciate reading our article about How to Install or Replace a Shower Drain.